检测认证人脉交流通讯录
塑料管材管件热稳定性试验专用试验箱
- 用 途：
- 塑料管材管件热稳定性试验专用试验箱主要用于管材在110℃下，管内介质为空气条件下进行的静液压试验，测定试样在规定的应力条件下，通过8760小时试验后,是否发生破坏。与静液压试验机配套使用可完成静液压状态下的热稳定性试验。
-
XCB系列塑料管材管件热稳定性试验专用试验箱
一、 产品描述
XCB-300Ⅱ型塑料管材管件热稳定性试验专用试验箱主要用于管材在110℃下，管内介质为空气条件下进行的静液压试验，测定试样在规定的应力条件下，通过8760小时试验后,是否发生破坏。与静液压试验机配套使用可完成静液压状态下的热稳定性试验。
二、 产品特点
1、双层隔热玻璃门、内置观察灯，即方便用户观察试验情况，又避免了意外烫伤。
2、合理的排水装置可及时排除试验失败工位产生的积水，减少对其它工位的影响。
3、厚达90mm的保温层，降低了试验成本，提高了仪器的可靠性。
4、加热器具有自保护功能，避免了加热器的意外损坏。
5、完善的漏电保护，过热保护装置提供了对仪器及使用人员的最佳防护。
6、全不锈钢框架和内胆，不仅美观同时增强了抗腐蚀性。
7、独特的夹具排气设计，大大减少了试验人员的劳动强度。
8、试样在试验过程中处于悬挂状态，使其符合试验标准要求。
三、符合标准
标准号
标准名称
GB/T6111-2003
《流体输送用热塑性塑料管材耐内压试验方法》
GB/T18742.2
《冷热水用聚丙烯管道系统》
GB/T18993.1—18993.3
《冷热水用氯化聚氯乙烯管道系统》
ISO10508
《冷热水系统用热塑料管材和管件》
四、技术参数
型 号： XCB-300Ⅱ
试验箱控温范围： 室温-120℃
控温精度： ±1℃
温度示值误差： ±0.5℃
温度均匀度： ±1℃
适用的最大管径： Φ63mm
试样最大长度： 500mm
夹装工位： 12路
电 源： (220-15% ～220+10%)VAC 50Hz 3.0kW 单相三线
XCB series plastic pipe fittings special test box for thermal stability test
I. Product description
XCB-300Ⅱ type plastic pipe fittings thermal stability test special test box is mainly used for pipe at 110℃, the tube medium is air under the condition of hydrostatic test, determine the sample under the specified stress condition, through 8760 hours of test, whether there is damage. It can be used with hydrostatic testing machine to complete the thermal stability test under hydrostatic state.
Two, product features
1, double layer insulated glass door, built-in observation lamp, which is convenient for users to observe the test situation, but also avoid accidental burns.
2, reasonable drainage device can timely eliminate the water generated by the test failure station, reduce the impact on other stations.
3, thick insulation layer up to 90mm, reduce the cost of the test, improve the reliability of the instrument.
4, the heater has self-protection function to avoid the accidental damage of the heater.
5, perfect leakage protection, overheating protection device provides the best protection for the instrument and the user.
6, all stainless steel frame and liner, not only beautiful and enhance corrosion resistance.
7, unique fixture exhaust design, greatly reduce the labor intensity of the test personnel.
8. The sample is suspended during the test to meet the test standards.
Three, meet the standards
Standard no.
The name of the standard
GB/T6111-2003
"Test Method for Internal Pressure Resistance of thermoplastic Pipes for Fluid Transport"
GB/T18742.2
Polypropylene piping System for Hot and Cold water
GB/T18993.1-18993.3
Chlorinated polyvinyl chloride piping System for Hot and cold water
ISO10508
"Hot Plastic Pipes and Fittings for Cold and Hot Water Systems"
Four, technical parameters
Model number: Ⅱ XCB - 300
Temperature control range of test chamber: room temperature -120℃
Temperature control accuracy: ±1℃
Temperature error: ±0.5℃
Temperature uniformity: ±1℃
Maximum applicable pipe diameter: φ 63mm
Maximum length of sample: 500mm
Clamping station: Road 12
Power source: (220-15% ~ 220+10%)VAC 50Hz 3.0KW single-phase three-line
