Silicone Rubber "Heat Cured Paste", furnished as sheets.

PVDF塑胶料UL认证

PMC塑胶料UL认证

Asphalt, potting compound, furnished as paste.

CR塑胶料UL认证

FEP塑胶料UL认证

SAN塑胶料UL认证

PPE塑胶料UL认证

PA46塑胶料UL认证

FEP塑胶料UL认证

ASA塑胶料UL认证

DMC塑胶料UL认证

Epoxy Effusing Varnish, furnished as liquid.

E/VAC塑胶料UL认证

LCP塑胶料UL认证

UF塑胶料UL认证

PPO塑胶料UL认证

PPA塑胶料UL认证

Acrylic, flame retardant, furnished as sheets.

Adhesive with Chloroprene Rubber, flame retardant, furnished as liquid.

Aramid Insulating Paper, furnished as rolls.

Asphalt base potting compound, furnished as paste.

Butyl Rubber, furnished as plaque.

CPE塑胶料UL认证

DAP塑胶料UL认证

Epoxy Resin Potting Compound, heat stabilized, furnished as pellets.；Epoxy Resin Potting Compound, furnished as pellets.

Glass Fiber Reinforced Unsaturated Polyester with Gel coat of unsaturated Polyester, furnished as Molded Parts

Epoxy Resin, furnished as two liquid components.；

HFP塑胶料UL认证

IBR塑胶料UL认证

FRPE胶料UL认证

EVA胶料UL认证

Magnetic Plastic Material, furnished as sheets.

Melamine Polyester Moulding Compound, furnished as granular??pellets or powder.

X-Fiper

Urea Melamine Formaldehyde, furnished as pellets.

Silicone - Heat cured, furnished as two liquid components.

Sealed cell, lead acid batteries with pressure release vents.

SB塑胶料UL认证

Rubber, magnet, furnished as finished parts.

Rubber, bonded anisotropic rubber magnet, furnished as pellets.

PVF胶料UL认证

PVAC胶料UL认证

PTFE胶料UL认证

PPT胶料UL认证

1 Scope

1.1 These requirements cover tests for flammability of polymeric materials used for parts in devices and appliances. They are intended to serve as a preliminary indication of their acceptability with respect to flammability for a particular application.

1.2 The methods described in this Standard involve standard size specimens and are intended to be used solely to measure and describe the flammability properties of materials, used in devices and appliances, in response to a small open flame or radiant heat source under controlled laboratory conditions.

1.3 The tests in the Standard for Tests for Flammability of Small Polymeric Component Materials should be used to evaluate small components which contain materials that can not be fabricated into standardized specimens in the minimum use thickness and subjected to applicable preselection tests in UL 94. Test procedures in UL 1694 are applicable to small components with an overall volume of less than 2500 mm3 (0.15 in3). UL 1694 is generally not applicable to small components with an overall volume greater than 2500 mm3 (0.15 in3).

1.4 The final acceptance of the material is dependent upon its use in complete equipment that conforms with the standards applicable to such equipment. The flammability classification required of a material is dependent upon the equipment or device involved and the particular use of the material. The performance level of a material determined by these methods shall not be assumed to correlate with its performance in end-use application. The actual response to heat and flame of materials depends upon the size and form, and also on the end-use of the product using the material. Assessment of other important characteristics in the end-use application includes, but is not limited to, factors such as ease of ignition, burning rate, flame spread, fuel contribution, intensity of burning, and products of combustion.

1.5 If found to be appropriate, the requirements are applied to other nonmetallic materials.

1.6 These tests, with the exception of the Radiant Panel Test in Section 10, are not applicable to the evaluation of parts where the thickness exceeds 13.0 mm or where the surface area exceeds 1 m2. These requirements do not cover polymeric materials when used for building construction, finishing, or contents such as wall and floor coverings, furnishings, decorative objects and so forth. In addition, the fire resistance (in terms of an hourly rating), flame spread, smoke characterization, and heat release rate is not evaluated. Other fire tests exist and shall be used to evaluate the flammability of materials in the intended end-use-product configuration.

Cover

Transmittal

Table of Contents

Body

INTRODUCTION

1 Scope

2 References

3 Definitions

4 Significance of Tests

5 Apparatus

6 Conditioning

TESTS

7 Horizontal Burning Test; HB

8 50W (20 mm) Vertical Burning Test; V-0, V-1, or V-2

9 500 W (125 mm) Vertical Burning Test; 5VA or 5VB

10 Radiant Panel Flame Spread Test

11 Thin Material Vertical Burning Test; VTM-0, VTM-1, or VTM-2...

12 Horizontal Burning Foamed Material Test; HBF, HF-1, or HF-2...

MARKING

13 General

GUIDANCE FOR ACCEPTING ALTERNATE MANUFACTURING LOCATIONS

电子线UL758认证，灯具UL认证，电线电缆UL认证，QMMY2 UL746D注塑件认证，UL969 PGDQ2标签认证，连接器UL认证，灯饰CCC认证，线路板组装VZQC2认证，UL969 PGAA标签认证，UL588圣诞产品认证，软线UL62认证代理，PCBA线路板组装ZPVI2认证，电容UL认证，开关UL认证，网络线UL444认证，锂电池、镍锰电池UL认证，水晶头UL1863认证，导电泡棉UL认证，光伏电缆UL认证，UL817插头认证，ECBT2 UL1997连接器认证，热缩套管UL认证，功率线UL13认证，UL507直流交流风扇认证，UL最新RSCS环保认证，阻燃套管UL认证，火灾报警线UL1424认证，UL2089车载充电器认证，UL1059端子台认证，塑胶电镀处理UL认证，光纤UL1651认证，UL355卷线器认证，UL486接线端子认证，UL486接线端子认证 塑胶料QMFZ2认证，UL764线束认证，UL310快接端子认证，UL1446绝缘系统认证，开关VDE认证，各国电线电缆认证，各国插头认证
详询Sunny 陶13913142465 QQ1822971259